True Keyless Pro — Smart module for motorbikes
True keyless — your phone in your pocket replaces the physical key for daily rides. Turn signals cancel automatically after a maneuver. Trip computer remembers all ride data. Built-in OBD engine diagnostics.
Keyless ignition for motorbikes.
True Keyless Pro — a powerful and flexible keyless system for motorcycles, including smart auto-canceling turn signals, a trip computer, and OBD engine diagnostics. Phone in pocket = ignition key
What it is
True Keyless Pro — keyless ignition for your motorbike. Owner's phone in pocket = key. Turn ignition on with the starter button or the kill switch (whichever you prefer — adjust in the app). Adjust phone detection range to your habits.
Smart auto-canceling turn signals after a maneuver. Short click ON/OFF = 3 flashes (or 4 — adjustable). When left ON — flash by time or by distance. Set ON and then turned — cancel automatically after the maneuver. Driveway mode — turned on while stationary, cancel automatically after pulling out and accelerating. Everything is adjustable via the app on your phone.
Trip computer — remembers everything about your last 10 rides. Distance, time, stop duration, speed, best acceleration time, your motorcycle's battery condition.
Onboard diagnostics of the fuel injection system is always available via the True Keyless app. Read and clear error codes, turn off the Check Engine light after repairs.
If you ride away without your phone (Bluetooth connection lost) — the motorcycle will not stall while riding, but will warn you with sound alerts at 150 and 400 meters of the ride. You can go back for your phone or enter a PIN code for the next ignition turn-on. There is an audible engine overheat warning — the threshold is adjustable in the app.
How to use
Pair your phone
Compatible phones are Android and iOS with Bluetooth version higher than 4.2 (BLE). Turn the ignition key on and enter the PIN code. Open Bluetooth settings on your phone, find True Keyless-XXXXXX, and pair. This is needed only during installation or phone change.
Start the engine
Sit on the motorbike. Two quick presses of the starter button (or flip the killswitch — select in settings during installation) — ignition turns on. Then press the starter button — normal engine start.
Switch off
Two presses of the starter button with the brake held (or flip the killswitch off) — ignition turns off.
Backup start — PIN
If the phone is unavailable or dead: hold the starter button for 3 seconds until a signal → tap each PIN digit (pause between digits) → hold again for 3 seconds until a signal.
Phone-out-of-range warning
If you ride away without the phone, the system sounds alerts at approximately 150 and 400 meters. The engine does not shut off while riding.
Ignition ON, start, ignition OFF
Keep your phone in your pocket. Sit down. Two clicks on the starter — and you're off.
PIN code entry
PIN code entry
Compatibility
Compatible with motorbikes that have an electric starter and NO factory keyless/keyfob or chip-key immobilizer — for keyless operation. For smart turn signals to work, the motorcycle must have an electronic speed sensor.
Phone: For keyless — Android and iOS with Bluetooth Low Energy support. The configuration app works only on Android.
Not compatible with motorbikes that have a factory keyless/keyfob or a chip-key immobilizer, as well as those without an electronic speed sensor.
The product is designed for professional installation. If in doubt, consult your motorcycle mechanic.
Specifications
| Supply voltage (nominal) | 12 V |
| Supply voltage (operating) | 7-24 V |
| Current on IGN output | 5 A continuous, 7 A max |
| Current on IGN 2 output | 5 A continuous, 7 A max |
| Current through ST1, ST2 contacts | 5 A continuous, 7 A max |
| Standby current consumption | less than 0.5 mA |
| Operating temperature | -20 to +80 degrees C |
| Water protection | IP68 — fully sealed |
| Encryption algorithms | AES-CCM 128bit + SHA-256 |
| Dimensions | 100 * 50 * 25 mm |
| Weight | 45 g |
| Warranty | 2 years |
Kit contents
Electronic control unit — 1 pc.
1 m connector harness — 1 pc.
Plastic cable tie — 1 pc.
Instruction sheet — 1 pc.
Installation
EasyRide is wired in parallel with the stock ignition switch. If the switch has three circuits — the third circuit is connected via a relay (not included in the kit). The starter circuit must be connected according to the diagram — note that the unit's terminals allow connecting the starter only through the stock relay, direct connection is not allowed.
Exceeding the specified load current values is strictly prohibited. If higher currents flow through the ignition switch or starter circuit — use additional relays.
Typical installation time is 3 hours. The system is designed for professional installation.
